- You do not have any products in your shopping cart yet.
Restek EMAS Phono Preamplifier
RESTEK EMAS, High-End Dual-Mono Phono RIAA Preamplifier with BAL / SE Inputs (7) and Outputs.
[Finish: Black, Alu, Chrom, Champagne, Acryl]
Display Colour: Blue, Red, Green
Description
In hi-fi stereo playback of records, the phono preamplifier - or phono pre - is a decisive factor for amplifying and linearizing the small pickup voltages. It is important to pay close attention to its properties, since it determines the sound quality and possible use of the entire monitoring chain.
The RESTEK EMAS is more than just an ordinary PhonoPre. It has seven asymmetrical phono inputs and an additional asymmetrical high-level input. The RESTEK EMAS is the central switching point for systems with several turntables or sound bases. It manages and forwards all external sources. This is done by switching the signal sources, linearizing and amplifying or weakening the output signal as well as special adjustments to the sound boxes for sound optimization.
The RESTEK EMAS can be adapted to the pickup system in a wide range. Both moving coil (MC) and moving magnet (MM) systems are supported.
Internally, the EMAS consists of two separate, partially symmetrical, identical mono preamplifiers, each with two volume controls. So it has a total of eight potentiometers. The inputs are switched via high-quality signal relays, whereby the ground connections of the non-switched input sockets are separated from the device in order to avoid ground loops.
The input sensitivity of the selected phono input can be adjusted in a range from +32 dB to +67.5 dB. In this way, differences in volume when switching between the individual inputs can be compensated. Using the volume control, the signal can be attenuated down to - 95 dB or amplified up to +10 dB. The two separately controllable outputs can be leveled against each other in a range of ± 6 dB and, if desired, can also be set synchronously with each other.
The output drivers of the phono preamplifier establish the connection to the power amplifiers or active loudspeakers.
The low output resistance of 50 ohms and the maximum current of up to 200 mA of these driver stages enable correct line adaptation on the one hand and the use of sometimes inevitable long connection cables between the phono preamplifier and the power amplifiers without the music signal being impaired by the cables.
All parts of the electronics of the RESTEK EMAS are DC-coupled. This makes it possible to transmit even the lowest frequencies. This means that even in the lower frequency spectrum, transmission is distortion-free and phase-locked.
The noise of this phono preamplifier is exceptionally low and the crosstalk is only detectable at the measuring limit.
The claim to ease of use and great functionality is realized through the control option of all special functions using the remote control or a single button. In this way, the design of the PhonoPre remains puristically clear - just like all devices in the RESTEK E series.
With the phono preamplifier EMAS you have a device at your disposal that leaves nothing to be desired in terms of ease of use and sound characteristics. There is no better way to make vinyl - "the black gold" - sound.
Features of the PhonoPre EMAS from the E series
- Remote control infrared system
- Dimmable multifunction display
- Menu-driven one-button operation
- Double mono construction
- Seven phono RIAA inputs and a high level input
- Individually adjustable capacitive and ohmic impedances and amplification
- Symmetrical volume control
- Symmetrical and asymmetrical output
- Adjustable output levels
- German manufacturing
Technical specifications
- Frequency response: 10 Hz ... 20 kHz (+ -0.2dB)
- THD: <0.005%
- S / N ratio:> 103 dBA… 80 dBA based on 2 V rms depending on the amplification
- Crosstalk attenuation:> 106 dB
- Input impedance per input: 50 Ohm… 680 Ohm in 10 Ohm steps and 47 kOhm
- Input capacitance per input: 100 pF… 700 pF in 50 pF steps
- Gain per input: + 32dB… + 64dB at 1 kHz in 0.5 dB steps
- Output level: 10 V rms max.
- Output current: 200 mA rms max.
- Output impedance: 50 ohms
- Dimensions (WxHxD): 483 x 90 x 365 mm
- Weight: approx. 10 kg
- Display color: red, green or blue
- Versions of the front:
- Acrylic glass highly polished, aluminum black, champagne or silvery matt brushed, chrome-plated brass as well as special designs on request
Customer reviews
Unfortunately there are no review yet. Be the first who rate this product.
To this product we recommend also (for example):
For more information, please visit the home page for this product.